Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Stafford, TX
Gate access control and gate parts & welding in Stafford skew commercial, because Stafford itself does. This is one of Texas’s largest cities with no city property tax, which has pulled warehouses, distribution centers, and light-industrial parks thick along the US-90 Alt and Kirkwood Road corridors. That means the gate work here is heavier than in Sugar Land or Missouri City: more slide gates at loading docks, more card readers on tilt-up office parks, more welded steel repairs where a driveway contractor would walk away. Call (346) 375-5416 and you’ll reach a live person who can tell you whether it’s a board, a weld, or a motor, and what it costs before anyone drives out.
Why Stafford Homes Are Different
Most residential subdivisions in Stafford were built from the late 1970s through the 1990s, and the ornamental wrought-iron driveway gates from that era are now showing their age: chronic rust blooming along hinge welds, hinge pins wearing oval, posts leaning as the gumbo clay beneath them swells and shrinks through the seasons. Gulf Coast humidity stays above 80% much of the year, and it strips paint, pits steel, and corrodes control boards inside operator housings faster than anywhere inland. When a tropical system drops a foot of rain in a day, operators in low spots can sit submerged and need full motor-and-board replacement, not a tune-up. On the commercial side, the tilt-up warehouses built in the 1990s and early 2000s along the US-90 Alt corridor are hitting end-of-service-life on their slide gate operators all at once, and a technician who doesn’t stock FAAC and LiftMaster commercial parts and know those era-specific board wiring quirks ends up quoting a replacement because repair is too hard. We stock the parts and we know the wiring.
Our Main Stafford Services
Stafford homeowners and property managers call us most about these three jobs. Each has its own Stafford page with full pricing and details.
Gate Repair in Stafford
A gate that drags, screeches, or won’t close all the way on a Stafford lot is usually a hinge, a weld, or a limit-switch problem, made worse by years of humidity and shifting soil. Read what repair actually costs and which parts we replace most on our Gate Repair in Stafford page.
Gate Installation in Stafford
New driveway gates in Stafford need posts set deep enough and wide enough for gumbo clay that moves, plus coatings that survive Gulf Coast moisture. We measure, quote in writing, and never start until you’ve approved the number. Details and pricing live on the Gate Installation in Stafford page.
Gate Motor & Opener in Stafford
Stafford’s slide gate operators at industrial parks and the swing motors on 1990s subdivision gates are failing on a schedule, not randomly. Whether it’s a LiftMaster or a FAAC, the fix usually comes down to the board, the capacitor, or the travel limits. See Gate Motor & Opener in Stafford for the full breakdown.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Stafford
Gate access control in Stafford is more likely to mean a card reader on a tilt-up industrial yard along US-90 Alt than a keypad on a driveway, though we see both every week. The concentrated wave of 1990s commercial operators hitting end of life means a lot of the systems tied to those gates, phone entry panels, card readers, video intercoms, are failing alongside the motors they talk to. We service all of it, and we document every setting, every board, and every wiring change in a photo record before we leave. That’s the habit Adrian Vance brought over from commercial access-control work starting in 2014, and it means the next technician who touches your system won’t have to guess what was done. Our Gate Access Control hub has the deeper service breakdown; here are the two jobs Stafford calls us about most.
Keypad Entry
Signs you need it
Codes stop working, the keypad goes dead after rain, or tenants can’t get in after hours.
What it costs in Stafford
Keypad replacement in Stafford typically runs $250 to $550 installed, including programming and a weather-sealed housing.
How we do it
We trace the wiring back to the control board, test voltage at the keypad, replace or reprogram, and photograph the final settings.
Phone Entry
Signs you need it
Calls ring through but won’t open the gate, or the cellular dialer loses signal and residents get locked out.
What it costs in Stafford
Phone entry systems run $500 to $1,200 in Stafford, depending on whether it’s a cellular unit or a landline retrofit.
How we do it
We verify the relay that opens the gate, test signal strength on cellular units, and photograph the programming before closing up.
What Gate Access Control Costs in Stafford
| Item | Typical range in Stafford |
|---|---|
| Keypad replacement | $250 - $550 |
| Phone entry system | $500 - $1,200 |
| Card reader added to existing gate | $350 - $800 |
How much does keypad entry cost in Stafford?
A weather-sealed keypad with programming runs $250 to $550 installed. The range depends on whether we’re replacing a dead unit or adding keypad control to a gate that never had it. Call (346) 375-5416 for a written quote before any work starts.
Can you add card reader access to an existing Stafford gate?
Yes. We add card readers to existing gate operators for $350 to $800, depending on the operator’s board and whether new wiring needs to be pulled from the gate to the building. The quote is written and handed to you before we begin.
Gate Parts & Welding in Stafford
The 1970s-1990s ornamental gates on Stafford’s residential streets are at the age where a hinge pin finally wears through or a weld lets go, and the commercial gates on US-90 Alt carry the same problems at heavier scale. We weld on site, we replace what’s beyond saving, and we leave a photo record of every part number and every bead laid. See our Gate Parts & Welding hub for the full service range; here are the two jobs Stafford calls about most.
Hinge Replacement
Signs you need it
The gate sags at the latch side, scrapes the ground, or the hinge pin shows visible oval wear.
What it costs in Stafford
Hinge replacement in Stafford runs $150 to $400 per hinge, depending on whether we’re replacing the pin or the full welded assembly.
How we do it
We weld in the new hinge, re-level the gate, and photograph the completed assembly before we leave.
Custom Welding
Signs you need it
A cracked weld, a snapped picket, or a section that’s rusted through and needs new steel let in.
What it costs in Stafford
Custom welding repairs in Stafford run $120 to $350 per repair point, plus materials if new steel is needed.
How we do it
We grind out the failed material, weld in new steel, prime and paint the repair, and photograph it for your file.
What Gate Parts & Welding Costs in Stafford
| Item | Typical range in Stafford |
|---|---|
| Hinge replacement (per hinge) | $150 - $400 |
| Custom welding repair (per point) | $120 - $350 |
| Gate roller replacement | $180 - $450 |
Can you weld a gate post that’s leaning in Stafford’s soil?
Welding the post itself is rarely the fix; the post needs to be reset or replaced because Stafford’s gumbo clay moves and takes the post with it. We quote the post work and the weld separately so you see exactly what each costs.
Do you replace rollers on commercial slide gates in Stafford?
Yes, roller replacement runs $180 to $450 per gate, including removal of the old rollers and greasing the new set. We stock rollers for the common track sizes on US-90 Alt commercial installations.
Brands We Service in Stafford
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. On Stafford’s commercial corridors, we stock FAAC and LiftMaster parts locally because that’s what the 1990s integrators installed. On the residential side, we’re ready for Ghost Controls, Viking, and Linear boards the same day. See our brands for the full current list.
Pricing for Gate Repair in Stafford, TX
| Service | Typical range in Stafford |
|---|---|
| Keypad replacement | $250 - $550 |
| Phone entry system | $500 - $1,200 |
| Card reader added to existing gate | $350 - $800 |
| Hinge replacement (per hinge) | $150 - $400 |
| Custom welding repair (per point) | $120 - $350 |
| Gate roller replacement | $180 - $450 |
| Post replacement (residential) | $400 - $1,000 |
| Control board replacement | $300 - $850 |
What pushes a Stafford quote upward: severe rust requiring more steel let in, posts that need resetting because the clay has shifted them, and commercial slide-gate operators that need heavy-duty parts not residential-grade substitutes. Every price above is a written quote, handed to you before work starts, and agreed before we pick up a tool.
Neighborhoods We Serve in Stafford
We run residential and commercial calls all over Stafford, and a live person answers the phone around the clock. Same-day service is available for most repairs; bigger access-control or welding jobs get scheduled within the week.
- Meadow Village
- Stafford Oaks
- Colony Bend
- Fountain Lake
- US-90 Alt corridor (commercial)
Service Area - Cities Near Stafford
Vance Gate Repair serves Stafford and the surrounding communities. We also run calls to Sugar Land, TX, Missouri City, TX, Bellaire, TX, and Richmond, TX. Dispatch and scheduling are coordinated from our Houston office; crews serve Stafford locally.
Serving Stafford, TX - Our Local Coverage Area
We’re based in the Stafford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Stafford
For urgent repairs like a gate stuck open, we can usually have a technician in Stafford the same day. Routine work and larger welding or access-control jobs get scheduled within a few days. Call (346) 375-5416 and a live person will give you a straight answer on timing.
Most gate repairs don’t need a permit, but new installations or post work may, depending on the scope and the property’s location. We’ll tell you during the quote if a permit applies. The written price is yours before anything starts.
Yes. Stafford’s mix of residential subdivisions and light-industrial parks means we shift between driveway gates and loading-dock slide gates in the same day. We stock parts for both, and every job gets a photo record before we leave.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Stafford Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.